Custom Metal Gates for Landed Homes in Singapore: Materials, Designs and Cost Drivers
Quick answer: A custom metal gate for a landed home in Singapore is usually made from mild steel that is hot-dip galvanised and powder coated, aluminium, or stainless steel. Material, gate width, swing or sliding design, infill pattern, finish and any motor move the price most. Measure the opening before choosing a design.
This guide is for homeowners replacing a rusted gate, adding an auto gate, or rebuilding the front of a terrace, semi-detached or detached house. It covers which material holds up in Singapore's heat, rain and humidity, how swing and sliding gates compare, what URA allows, and the details a fabricator needs to give you an accurate quote.
When does a gate need to be custom made?
Ready-made gates come in fixed widths and heights. Landed homes rarely have fixed openings: driveways differ by a few centimetres from house to house, posts lean, floors slope towards the drain, and older houses often have a pedestrian gate beside the main one. A custom metal gate is built to the measured opening, so it closes square, the gap at the bottom stays even, and the lock lines up.

Custom also makes sense when you want the gate to match the facade, such as a laser-cut pattern that echoes a window grille, horizontal slats that line up with the boundary fence, or a colour matched to the roof.
Which material is best for a gate in Singapore's climate?
Singapore's humidity and frequent rain punish any coating that is chipped or any joint that holds water. The right material depends on how wide the gate is, how close you are to the sea, and how much upkeep you will accept.
Material | Strengths | Watch-outs | Usual finish | Relative cost |
|---|---|---|---|---|
Mild steel | Strong, stiff and easy to weld; the most economical for wide or heavy gates | Rusts wherever the coating is breached; heavy, so motors and hinges must be sized for it | Hot-dip galvanised, then powder coated | Lowest |
Aluminium | About a third of the weight of steel; does not rust red; good for sliding and auto gates | Less stiff, so wide spans need deeper sections; dents more easily | Powder coated or wood-grain coated | Medium |
Stainless steel (304 or 316) | No paint layer to fail; clean modern look | Highest material cost; grade 304 can tea-stain near the sea, where 316 holds up better | Brushed or hairline finish | Highest |
Wrought-iron style | Classic ornamental look | In Singapore this is usually mild steel with cast or forged details, so it needs the same rust protection | Galvanised and painted or powder coated | Medium to high, driven by detail |
For a deeper comparison of the three main metals, see our guide to mild steel vs stainless steel vs aluminium.
Swing gate or sliding gate?
The choice usually comes down to space. A swing gate needs a clear arc inside the compound for each leaf, and most are designed to open inwards so the leaves never swing over the road or pavement. A sliding gate needs a straight run of wall or fence beside the opening at least as long as the gate itself.

Feature | Swing gate | Sliding gate |
|---|---|---|
Space needed | A clear arc inside the compound | A side run as long as the opening |
Sloped driveway | Possible with rising hinges or shaped leaves | Usually easier, because the track is level |
Auto-gate motor | Arm or underground motors, one per leaf | One rack-and-pinion motor |
Upkeep | Hinges and gate stops | Track, rollers and guide wheels; the track must be kept clear of leaves and grit |
Best for | Wide frontages with room behind the gate | Short driveways, cars parked close to the gate, slopes |
Where neither fits, bi-fold and telescopic sliding gates fold or stack the leaves to save space, at the cost of more moving parts.
What drives the cost of a custom metal gate?
Two gates that both look like a standard driveway gate can be priced very differently. These are the things that move the number, roughly in order of impact:
Width and height. More metal, more welding and a heavier gate that needs stronger hinges, rollers or motor.
Material and section size. Stainless costs more than aluminium, which costs more than mild steel, and thicker or deeper sections add weight and price.
Infill design. Plain vertical bars are the quickest to make. Horizontal slats, laser-cut panels, perforated sheet and wood-look aluminium all add cutting, fitting or material cost.
Finish. Hot-dip galvanising plus powder coating costs more than paint, and it is the single biggest factor in how long a steel gate lasts.
Gate type and hardware. Sliding tracks and rollers, heavy-duty hinges, drop bolts, locks and handles.
Automation. Motor, remote, safety sensors, and a power point near the gate if there is none yet.
Site work. Removing the old gate, new posts or hacking, access for lifting, and installation.
Extras. A matching pedestrian gate, letterbox or intercom cut-out, or a house number panel.
Our guide to metal fabrication lead times in Singapore explains why galvanising and powder coating also add time to the schedule.
Are laser-cut gate panels worth it?
Laser-cut panels are the most popular way to give a landed home a gate that no neighbour has. A pattern is drawn, cut from a single sheet, and welded into the gate frame. Three things decide whether it works:
Open area. The share of the panel that is cut away decides how much privacy and airflow you get. A pattern that looks dense on a phone screen can look open at full height.
Scale. Details smaller than a few centimetres disappear when seen from the road, and very fine bridges between cuts are fragile.
Edges and coating. Every cut edge must be cleaned and coated properly, or rust starts there first.
Read more about how we approach laser cutting in Singapore.
Are there rules on gate height for landed homes?
Gates usually sit in line with the boundary wall, so the boundary wall rules are the ones to check. URA's Landed Housing e-Advisor states that boundary walls for detached houses shall not exceed 1.8 m. For strata landed housing, URA allows a combined retaining and boundary wall height of up to 2.8 m, of which the solid wall shall not exceed 1.8 m, and a boundary wall on top of a retaining wall must be porous, such as fencing.
Rules differ by house type and estate, so check the e-Advisor for your house before settling on a taller gate. If you live in a strata landed estate, check your MCST by-laws too.
How do you stop a new gate from rusting?
Specify hot-dip galvanising under the powder coat for mild steel, not paint alone.
Make sure hollow sections have drain holes and the bottom rail cannot hold water.
Avoid site welding after coating where possible, because every weld burns the coating off.
Touch up scratches early, and rinse salt and grit off gates near the coast or busy roads.
Keep sliding tracks clear so rollers do not grind through the coating.
What should you send a fabricator for a quick, accurate quote?
A photo and a few measurements are enough for a first estimate:
A photo of the opening taken from the road, with the posts visible.
The width at the top and at the bottom, and the height you want.
Whether the ground slopes, and which way.
Swing or sliding, and how much space you have behind or beside the opening.
The material and finish you are considering, and whether you want a motor.
One or two reference photos of gates you like.
Picture the new gate on your driveway. WhatsApp a photo of the opening to 9862 5243 with the word GATE and we'll tell you how we'd build it and what will drive the cost. No quote unless you ask.
Frequently asked questions
How long does a custom metal gate last in Singapore?
It depends far more on the finish and drainage than on the steel itself. A mild steel gate that is hot-dip galvanised, powder coated, drained properly and touched up when scratched will outlast a painted one by a wide margin. Aluminium and stainless steel gates avoid red rust altogether but still need their hardware checked.
Is aluminium or mild steel better for a driveway gate?
Mild steel is stronger and stiffer for its cost, so it suits wide, heavy or highly secure gates. Aluminium weighs about a third as much as steel and will not rust red, which suits sliding gates, auto gates and homes near the coast. For very wide spans, aluminium needs deeper sections to stay rigid.
Can I add an auto-gate motor to my existing gate?
Often, yes, if the gate is still rigid, the hinges or track are in good condition and there is a power point nearby. Heavy mild steel gates need a motor rated for their weight, and a sliding gate needs a level, clean track. If the frame has rusted through at the bottom rail, replacing the gate is usually the better spend.
Do I need approval to replace the gate of my landed house?
Replacing a gate within an existing boundary is generally minor work, but the height rules for boundary walls still apply and strata landed estates may have their own by-laws. Check URA's Landed Housing e-Advisor for your house type, BCA's list of building works that do not need plan approval, and your MCST if you have one.
Should I choose a swing or sliding gate for a sloped driveway?
A sliding gate usually copes better with a slope because the leaf runs along a level track instead of sweeping across the ground. A swing gate can still work on a gentle slope with rising hinges or leaves cut to follow the gradient, but it needs a clear arc inside the compound.
How do I keep a laser-cut gate private?
Choose a pattern with a smaller open area, put a solid or perforated backing panel behind the decorative layer, or use the laser-cut pattern only on the top section of the gate. Ask to see the pattern at full scale before cutting, because a pattern that looks closed on screen can look very open at 1.8 m tall.
Sources
Related reading
Ready when you are: WhatsApp 9862 5243 with the word GATE and a photo of your gate opening.
TR Metalworks · custom metal fabrication in Singapore · laser cutting, bending, rolling and shearing · workshop at JTC Space @ Tuas

Comments