top of page

Stainless Steel Kitchen Fabrication for F&B in Singapore: Tables, Sinks and Counters

3 days ago
5 min read

Quick answer: Stainless steel kitchen fabrication for F&B in Singapore means made-to-measure work tables, sinks, counters, shelves and wall cladding, usually in grade 304 stainless steel and sized to your floor plan. Go custom where standard sizes waste space or clash with columns, pipes and drains. Buy standard where standard fits.

This guide is for cafe, restaurant, hawker and central kitchen owners, and the interior designers and contractors fitting them out. It covers what can be fabricated, when custom is worth it, which grade of stainless to use, the build details that make a table last, and the SFA and PUB points to plan around.

What can be custom fabricated for an F&B kitchen?

  • Work tables with an undershelf, upstand and drawers

  • Sinks: single, double or triple bowl, with drainboards on either side

  • Wash hand basins for kitchen staff

  • Wall shelves, pot racks and plate racks

  • Service counters, bar counters and pass-through shelves

  • Wall cladding and splashbacks behind cooking and prep areas

  • Mobile stations and trolleys

  • Covers, trims, kick plates and corner guards

Custom or off-the-shelf: which makes sense?

Situation

Off-the-shelf

Custom fabricated

A straight wall that fits standard table lengths

Usually cheaper and quicker

Not needed

Columns, pipes, floor traps or odd corners

Leaves gaps or overlaps

Built to the measured space

Sink and work table in one run

Separate units with joints that trap dirt

One continuous top with welded-in bowls

Heavy equipment on the top

Light frames may flex

Top and frame reinforced for the load

Landlord or mall fit-out drawings needed

Supplier brochure dimensions only

Shop drawings that match the fit-out plan

Many kitchens end up with a mix: standard tables along the straight runs, and custom pieces for the sink run, corners and service counter.

Which stainless steel grade: 304, 316 or 201?

Comparison of 304, 316 and 201 stainless steel for F&B kitchens in Singapore: where each grade suits and what to watch out for

Grade

Best for

Watch-outs

304

Most food preparation surfaces, sinks and shelving

Can pit with prolonged exposure to salt, brine or chlorine-based cleaners

316

Brine and seafood areas, salty marinades, coastal and outdoor kitchens

Costs more than 304; only needed where chlorides are a real problem

201

Light, dry, budget use

Less nickel and lower corrosion resistance; may stain with salty or acidic food and strong cleaners

For a wider comparison of metals, see our guide to mild steel vs stainless steel vs aluminium.

Which build details make a work table last?

Labelled diagram of a custom stainless steel work table for an F&B kitchen: upstand, raised edge, 1.2 to 1.5 mm top, welded-in sink, undershelf, adjustable feet and 850 to 900 mm working height
  • Top thickness and stiffening. Tops of 1.2 mm to 1.5 mm with stiffeners underneath are common. Reinforce where heavy equipment sits instead of thickening the whole top.

  • Upstand at the wall. A raised back edge stops spills from running down behind the table.

  • Raised edge for wet areas. A lip around the front edge keeps water on the table and off the floor.

  • Continuous welds and rounded corners. Gaps and sharp internal corners trap food and are hard to clean.

  • Adjustable feet or castors. Kitchen floors slope to the drains, so fixed tables need levelling feet; mobile ones need braked castors.

  • Undershelf height. Set it to clear your containers and the cleaning mop.

  • Sound-deadening under sink bowls. It cuts the drumming noise during washing.

What does SFA look for in a kitchen?

SFA's self-checklist for food shops asks for the walls of the preparation and servery area to be lined with glazed tiles or other suitable impervious materials to a height of not less than 1.5 m, so they can be cleaned easily. It also asks for at least one wash hand basin with hand soap for the workers in the kitchen. Stainless steel splashbacks and wall cladding are a common way to meet the impervious, easy-to-clean requirement around prep and cooking areas.

Drainage needs planning too. PUB states that owners must get NEA's and PUB's approval before installing grease traps, and that grease traps are sized to BS EN 1825. Confirm the grease trap and floor trap positions with your plumber or Qualified Person before the sink run is fabricated, so the bowls and outlets line up.

This is a summary, not licensing advice. Check SFA's current checklist for your licence type before you finalise the layout.

How do custom pieces fit into your fit-out timeline?

  1. Confirm the layout and your equipment list, including the exact dimensions of ovens, fridges and dishwashers.

  2. Measure on site after walls, tiling and screeding are done, or work from confirmed fit-out drawings.

  3. Agree sink bowl positions with the plumbing points, floor traps and grease trap.

  4. Check delivery and installation windows if you are in a mall or a building with loading rules.

Our guide to metal fabrication lead times in Singapore covers how to avoid last-minute delays before opening day, and our metal fabrication cost guide explains what moves the price.

What should you send for a quote?

  1. A floor plan with dimensions, or photos of each wall with a tape measure in view.

  2. Your equipment list with sizes.

  3. The pieces you need: tables, sinks, shelves, counters or cladding.

  4. Sink bowl sizes, how many bowls, and which side the drainboard goes.

  5. Working height: most work tables are built around 850 mm to 900 mm high.

  6. Grade: 304, or 316 for salty and wet areas.

  7. Your target opening date.

Picture the kitchen with every table and sink in place. WhatsApp your floor plan or a photo of the space to 9862 5243 with the word KITCHEN and we'll tell you which pieces are worth making custom and which you can buy off the shelf. No quote unless you ask.

Frequently asked questions

Does SFA require stainless steel in an F&B kitchen?

SFA's requirements focus on surfaces being smooth, impervious and easy to clean, and its food shop checklist asks for the walls of the preparation and servery area to be lined with glazed tiles or other suitable impervious materials to at least 1.5 m. Stainless steel is the most common way to meet this for work surfaces and splashbacks, but it is not the only acceptable material.

How thick should a stainless steel work table top be?

Tops of 1.2 mm to 1.5 mm with stiffeners welded underneath are common for general preparation. Where heavy equipment such as a combi oven or mixer sits on the table, the top and frame should be reinforced for that load rather than simply made thicker.

What is the difference between 304 and 201 stainless steel?

Grade 201 replaces part of the nickel in 304 with manganese, which makes it cheaper but less resistant to corrosion. It is common in budget tables and can stain or pit with salty or acidic food and strong cleaning chemicals. Grade 304 is the usual choice for food preparation surfaces.

Can a sink and a work table be made as one piece?

Yes. A continuous top with sink bowls welded in has fewer joints for water and food to collect in, and it can be sized exactly to the wall. It does need the plumbing points, floor traps and grease trap position confirmed before fabrication.

Can custom stainless steel tables be moved for cleaning?

Yes, if they are built on castors with brakes. Fixed tables are usually built on adjustable feet so they sit level on a sloped kitchen floor. Plan the gap to the wall or a sealed upstand so the area behind the table can be cleaned.

Who connects the sinks and grease trap?

Sink connections are plumbing work for your licensed plumber. PUB requires owners to get NEA's and PUB's approval before installing grease traps, so your plumber or Qualified Person should confirm the grease trap position before the sink run is fabricated.

Sources

Related reading

Opening soon? WhatsApp 9862 5243 with the word KITCHEN and your floor plan.

TR Metalworks · custom metal fabrication in Singapore · laser cutting, bending, rolling and shearing · workshop at JTC Space @ Tuas

Comments


Copyright © 2026 TR Metalworks

bottom of page